The DJI Mavic Air Carrying Case with shock-resistant hard shell casing perfectly holds the Mavic Air drone for safe and easy transportation. Size: 190 x 110 x 71mm.
The DJI Zenmuse X7 DL 24mm F2.8 LS ASPH Lens is designed to work seamlessly with DJI’s X7 high-end Super 35 image sensor to deliver beautiful aerial photography. The lens features a carbon fibre body, making it both lightweight and durable, as well as a maximum aperture of f2.8, mechanical shutter and a 0.65m close focusing distance.
The DJI Zenmuse X7 DL 35mm F2.8 LS ASPH Lens with DL-mount incorporates DJI's latest technologies to deliver stunning aerial photography. The lens is designed to work seamlessly with the DJI X7's high-end Super 35 image sensor and features a carbon fibre body, making it both lightweight and durable. It offers a maximum aperture of f2.8, mechanical shutter
The DJI Inspire 2 CINESSD 480G uses an NVMe logical device interface specification, features four PCI Express ports and supports FAT32/exFAT file formats. The Inspire 2 can record videos at write speeds of up to 4.2Gbps, providing enough data to meet demanding filmmaking needs. Also available in 120GB and 240GB.
The DJI Ronin-MX HDMI to Mini HDMI Cable for SRW-60G is used to connect cameras with HDMI C ports, such as Canon 5D or Panasonic GH3, to the SRW-60G Transmitter. One end features straight HDMI A plug and the other an angled HDMI C plug. Cable length 80cm.
The DJI Osmo Battery (2 Pin) to DC Power Cable is used to connect a DJI device with a DC port and one of the following DJI Intelligent Batteries as a power supply for the device.
The DJI Ronin-S/SC Phone Holder securely attaches to the camera's hot shoe mount to enable ActiveTrack 3.0 and attaches to the RSA port when using the mobile device as a camera monitor, enabling quick access to camera parameter adjustment.
Some of the supported lenses for the DJI Inspire 1 quadcopter drone require a balancing weight. This Balancing Ring (33g) from DJI features a 46mm thread and is designed to stabilise the Panasonic Olympus 17mm f1.8 M.ZUIKO lens on the Zenmuse X5 gimbal when shooting to maximise performance. The balancing ring must be installed on the camera lens when a
The DJI Ronin-SC RSS Control Cable for Panasonic connects the camera control port of Ronin-SC to a Panasonic camera for camera control.
A spare or replacement DJI Focus Rechargeable Battery 1700mAh for DJI Focus Remote Controller (part 22).
Wirelessly charge up to three DJI Spark Intelligent Flight Batteries on the go with the DJI Spark Portable Charging Station. It offers an impressive power of 5000mAh and will charge up to three Spark batteries in 2.5 hours when fully charged. It also provides power to mobile devices via its USB port, and the Charging Station itself charges in just 1 hour
This is a spare or replacement DJI Osmo Articulating Locking Arm for the DJI Osmo car mount. It can also be used with the DJI tripod to provide extra stability for the Osmo camera.
DJI's official collapsible sun shield hood, designed to stop sunlight from reflecting brightly off the view of your smartphone display. Suitable for use with the Inspire 1 and Phantom 3 transmitters. Easy to carry and compatible with the iPhone 6 Plus and most smart phones. The Smartphone device size should not exceed 165mm x 87mm x 85mm.
Precisely engineered for racing, DJI Goggles Racing Edition are compatible with an OcuSync video transmission module and a high-performance camera module, which work together to transmit digital video signal from up to 7km away with latency as low as 50 ms,1 in addition to analog signal. Fly with smooth, clear video and experience the thrill of drone racing
Compatible with CrystalSky monitors and the Cendence remote controller, this 2s 4920 mAh DJI Intelligent Battery has excellent discharge performance at low temperatures and charges quickly. One battery offers four to five hours of operating time for a 7.85" CrystalSky monitor, five to six hours for a 5.5" CrystalSky monitor, and four hours for a Cendence
Precisely engineered for racing, DJI Goggles Racing Edition Combo are compatible with an OcuSync video transmission module and a high-performance camera module, which work together to transmit digital video signal from up to 7km away with latency as low as 50 ms,1 in addition to analog signal. Fly with smooth, clear video and experience the thrill of drone
The Inspire 2 remote controller can be charged by connecting it to an Inspire 2 Intelligent Flight Battery using this DJI Inspire 2 Remote Controller Charging Cable.
The DJI Ronin-MX Remote Start/Stop is designed to be used with a Ronin series gimbal or DJI Focus to control the camera for video recording or taking photos. When using the Remote Start/Stop with the Ronin-MX and Matrice 600, press the Shutter button or the Video Recording button to take photos or record video.
Used to connect the DJI Focus motor to the DJI Remote Start/Stop, this DJI Ronin-MX Remote Start/Stop Focus Power and Data Cable provides power and signal communication from the DJI Focus motor to the DJI Remote Start/Stop, so that you can take photos or record video using the DJI Focus.
An official DJI Zenmuse X5S Balancing Ring to be mounted on an Olympus M.Zuiko 12mm f2.0, 17mm f1.8 and 25mm f1.8 lenses for more stable shooting with the Zenmuse X5S.
The DJI Ronin-S Multi-Camera Control Cable (Type-B) allows for the control of cameras installed with a Type-B port through the Ronin-S camera Control Button. This gives the user access to functions including photography, parameter configuration, and much more. The cable measures 20cm and is compatible with the Ronin-S. This cable connects the Camera Control
The DJI Osmo Pocket Smartphone Adapter (Type-C, USB-C) connects the Osmo Pocket to a smartphone in addition to unlocking more features on the DJI Mimo app. The handy device measures only 24.9 × 13.2 × 6.1mm and weighs 1.8g.
The DJI Osmo Pocket Extension Rod is conveniently retractable up to 500mm and features a phone holder, multiple mounting brackets, and a standard 1/4-inch tripod mount located at the bottom; connecting the Osmo Pocket with other accessories. The Osmo Pocket can be controlled with the extension rod when used in conjunction with the Osmo Pocket Wireless Module
The DJI Osmo Pocket Waterproof Case keeps the Osmo Pocket dry at depths up to 60m. The casing has been specifically designed for the Osmo Pocket; fitting it perfectly and therefore keeping it securely in place without unwanted movements. There are 2 mounting brackets located at the bottom of the case for the attachment to other equipment. The case also
The DJI Osmo Pocket Anti-fog Inserts are fantastic for shooting underwater with the Osmo Pocket Waterproof Case as they reduce moisture and prevent the case from fogging up. They weigh 0.75g and measure 75 × 15.5 × 1.0mm. They should be stored in a dry environment and replaced after use.
An official DJI Zenmuse X5S Balancing Ring to be mounted on a Panasonic 14-42mm f3-5.6 Lens for more stable shooting with the Zenmuse X5S camera.
The DJI Ronin-SC Multi-Camera Control Cable (Type-C) connects a camera with a Type-C port to the Camera Control Port of Ronin-SC for camera control.
The DJI Osmo 1/4" and 3/8" Mounting Adapter is designed to increase the number of tools you can use with the Universal Mount. It is used to attach accessories with a 1/4" or 3/8" thread such as the Tripod.
The DJI BG18 Grip makes Ronin-SC compatible for handheld use. A 2450 mAh built-in battery powers the gimbal for up to 11 hours.
The DJI Osmo Pocket Smartphone Adapter (Lightning, USB-C) connects the Osmo Pocket to a smartphone in addition to unlocking more features on the DJI Mimo app. The handy device measures only 24.9 × 13.2 × 6.1mm and weighs 1.8g.
The DJI Osmo Pocket ND Filters Set created especially for the Osmo Pocket; offers a combination of filters increasing creativity. Included filters are as follow: ND4, ND8, ND16, and ND32. These allow 1/4, 1/8, 1/16, and 1/32 of incoming light through respectively, equal to 2/3/4/5-stop filters. Thanks to the ND filters reducing the amount of light reaching
The DJI Ronin-MX RSS Control Cable For Sony is used to connect the Remote Start/Stop Camera Port to Sony cameras.
The DJI Inspire 2 Intelligent Flight Battery Charging Hub is designed for use with the Inspire 2 Battery Charger. It charges up to four Intelligent Flight Batteries simultaneously and will intelligently charge batteries in sequence according to battery power levels from high to low, if batteries are not paired. Charge time for 2 batteries is 90 minutes
The DJI Ronin-MX HDMI to Micro HDMI Cable for SRW-60G is used to connect a camera via HDMI D, such as Panasonic GH4 or Sony A7, to the SRW-60G Transmitter. One end features a straight plug HDMI A plug and the other an HDMI D angled plug. Cable length 80cm.
The DJI Osmo Pocket Charging Case offers a generous 1500mAh of power facilitating longer shooting times. This handy device features a spin-to-open design; charges the Osmo Pocket on the go, and provides convenient storage. The charging case can hold 2 microSD cards, 4 ND filters, and 2 smartphone adapters. The device weighs only 169g and measures 47.9 ×
The DJI Focus Accessory Support Frame mounts the motor in a variety of positions to match a variety of lenses, and attaches it firmly to the Lens Gear Ring. It can be used for the inspire 1, Ronin and Ronin-m.
Use the DJI Ronin-SC Multi-Camera Control Cable (Multi-USB) to connect your Sony camera to the Ronin-S Camera Control Port. The Ronin-S Camera Control Button can be used to control the shutter, autofocus, and recording process.
The DJI Ronin-MX SRW-60G is a short range wireless video link, which can transmit real time HD video or images for up to 10 meters. Containing both a transmitter and a receiver, it is not only suited for the Ronin-MX and Matrice 600, but can also be used with the Ronin series of handheld gimbals. Convenient video transmission in a meeting room or at home
Replaces the Triple Mount Suction Cup Base on the DJI Osmo Car Mount. A 1/4" screw thread allows users to attach different tools and accessories, like the Extension Rod. Note: When used with a camera, make sure that the base is unlocked to prevent scratching the camera.
This DJI Ronin-MX RSS Power Cable is used to connect RSS to Lightbridge 2 port on the Ronin-MX gimbal for simultaneous communication and charging.
The DJI Inspire 2 CINESSD 240G uses an NVMe logical device interface specification, features four PCI Express ports and supports FAT32/exFAT file formats. When using a 480GB or 240GB CINESSD, the Inspire 2 can record videos at write speeds of up to 4.2Gbps, providing enough data to meet demanding film making needs. Also available in 120GB and 480GB.
The DJI Inspire 2 CINESSD Station is used to connect the DJI CINESSD into a computer for fast, efficient file transfer.
The DJI Inspire 2 Carrying Case has been made to securely hold the DJI Inspire 2 drone and its accessories. It’s made of strong, elastic expanded polypropylene with a metal frame to provide both lightness and strength. The upper and lower outer shells are detachable, allowing the upper shell to be used as a take-off platform.
The DJI Mavic 2 Aircraft Sleeve allows you to store your Mavic 2 Pro/Zoom drone easily while going out. The outside of the sleeve is made from a wear-resistant, water-resistant, and durable material. The inside of the sleeve is made from a soft and smooth material, protecting your Mavic 2 from surface wear.
This is a DJI Goggles RE Mono 3.5mm to Mono 3.5mm Cable for the DJI Goggles Racing Edition. The cable connects the coach interface of a third-party remote controller and the auto interface of DJI Goggles RE to transmit control signal from the remote controller to the aircraft.
Specifically made for the Osmo+ and Zenmuse Z3 Camera, this DJI OSMO ND16 (4-stop) Filter reduces the amount of light coming into the sensor. It gives you the freedom to create your own work by allowing more control of the camera's aperture, exposure time and sensor sensitivity settings. Put more simply, the ND filter helps avoid overexposed photos.
Designed for the Ronin and Ronin-M hand-held gimbals, this DJI Ronin Battery Power Distributor has a P-Tap power connector that can supply power to the gimbal and other onboard devices (such as a RED camera). The power connector is easy to connect and remove.
Used to install the Quick Release Propellers onto the Inspire 2, the DJI Inspire 2 Quick Release Propeller Mounting Plate kit is designed to add protection between the propeller and the propeller mount, reducing wear and extending the life of your propeller.
The DJI Inspire 2 GPS Module provides the Inspire 2 Remote Controller with accurate positioning coordinates, enabling the use of dynamic home points and offering remote controller positioning information during ActiveTrack.
The DJI Inspire 2 180W Power Adapter charges the DJI Inspire 2 drone remote controller and battery using AC power. It takes approximately 1.5 hours to fully charge an Inspire 2 Intelligent Flight Battery or 2.5 hours to charge an Inspire 2 remote controller. When charging both devices together, charging may take longer than 2.5 hours. Mains AC cable not
Both ends of the DJI Ronin-MX HDMI to HDMI Cable for SRW-60G feature straight plugs. It is used to connect cameras with HDMI A ports, such as the RED series, to the SRW-60G Transmitter. Cable length 80cm.
The DJI Inspire 2 CINESSD 120G uses an NVMe logical device interface specification, features four PCI Express ports and supports FAT32/exFAT file formats. It’s also available in 240GB and 480GB.
The DJI Matrice 600 Black Remote Controller integrates video downlink and aircraft control into one system. It operates at 2.4GHz with a maximum signal transmission range of 5km. It features a number of standard and customisable buttons that allow users to quickly access certain aircraft functions, such as taking and reviewing photos/videos, as well as
The DJI Inspire 2 Propeller Guard safeguards the propellers on your DJI Inspire 2 drone to protect people and objects from spinning propellers, ensuring a long, safe flight. Made from carbon fibre with epoxy resin, these guards are not only light, but also 50 times stronger and 100 times more rigid than standard engineering plastics, making them exceptionally
The DJI Battery (10 PIN-A) to DC Power Cable is used to connect a DJI device with a DC port and the Phantom 4 Intelligent Flight Battery (model PH4-5350mAh-15.2V) as a power supply for the DJI device.
The DJI Ronin RED Power Cable is used to connect the Ronin and Ronin-M Battery Power Distributor to a RED camera or another camera with the same connector port. The RED power cable is also compatible with the Ronin and Ronin-M gimbal and has a length of 50cm.
This DJI Ronin-MX Counter Weight (270g) is part of the Ronin-M & Ronin-MX Counterweight Set. The Counterweight Mounting Plate is required for mounting onto your Ronin. If unable to balance your Ronin using all parts of the Counterweight Set, purchase extra Counterweights as required.
The DJI Focus Handwheel 2 Remote Controller Stand mounts the DJI Focus Handwheel 2, DJI Focus Handwheel, and DJI Focus. By allowing the Focus, Focus Handwheel 2, or Focus Handwheel to connect to the Cendence Remote Controller you can fly while adjusting focus, aperture, and zoom easily.
The DJI Goggles RE Mono 3.5mm to Mini DIN Cable connects the coach interface of a third-party remote controller and the auto interface of DJI Goggles Racing Edition to transmit control signal from the remote controller to the aircraft.
DJI Ronin-MX Power Cable for Transmitter of SRW-60G is used to connect SRW-60G Transmitter for charging.